![]() |
[ شرح] : طريقع عمل جيلبريك الفيرموير 3.0
أطلق فريق Dev-Team أداة RedSn0w التي ستقوم محل QuickPwn لعمل جيلبريك لأجهزة الأيبود والأيفون بعد الترقية للفيرموير الجديد 3.0
هذه الأداة هي كل ما تحتاجه اذا كنت من أصحاب الآي-فون الجيل الأول iPhone 2G أو من أصحاب الأيبود تاتش الجيل الأول والثاني. كل ما عليك فعله هو ترقية هاتفك الي الفيرموير 3.0 ثم أسخدام برنامج RedSn0w ليقوم بعمل جيلبريك و فك حماية الشبكة لأصحاب الآي-فون الجيل الأول iPhone 2G. أما أذا كنت من أصحاب الآي-فون 3G المغلق علي شبكة واحدة فهذه الأداة سوف تساعدك فقط في عمل تفعيل للهاتف وجيلبريك وأنزال برنامج سيديا ولكن لن يستقبل هاتفك شبكة الجوال لأن برنامج YellowSn0w لا يعمل علي الفيرموير الجديد 3.0 وننتظر صدور برنامج UnltaSn0w في خلال أيام حتي يقوم بفك قفل الشبكة لأصحاب الآي-فون 3G والفيرموير 3.0 و أصحاب الأيفون 3GS http://www.iphoneislam.com/wp-includ...icon_smile.gif أولاً تحية لهم , ثانياً ليس لهم شيئ الأن. لا جيلبريك ولا فك حماية الشبكة. ولا يوجد أخبار عن إمكانية ذلك في الوقت الحالي. طريقة التثبيت..
Create a folder on your desktop called Pwnage Download RedSn0wfrom here or here and place it in the Pwnage folder. Likewise, download the latest 3.0 firmware from below and place it in the same folder. 3.0.0 (3G): iPhone1,2_3.0_7A341_Restore.ipsw Extract the RedSn0w zip file to the Pwnage folder. http://1.1.1.4/bmi/www.iClarified.co.../16370-500.png Step Two Connect your iPhone to the computer and launch iTunes. http://1.1.1.1/bmi/www.iClarified.co...6382/16382.png Select your iPhone from the list of devices on the left. Now hold down shift and click the Restore button. Restore is preferred as it won't create any wasted space on your iPhone. http://1.1.1.1/bmi/www.iClarified.co.../16383-500.png Navigate to the Pwnage folder on your desktop and select the firmware ipsw. Click the Open button to continue. http://1.1.1.3/bmi/www.iClarified.co.../16385-500.png Step Three Once iTunes has finished updating your iPhone to the desired firmware you may launch redsnw0w.exe from the Pwnage folder on your desktop. http://1.1.1.1/bmi/www.iClarified.co...6384/16384.png Step Four Once RedSn0w opens click the Browse button http://1.1.1.3/bmi/www.iClarified.co...6371/16371.png Step Five Select the firmware ipsw we placed in the Pwnage folder on our desktop then click Open http://1.1.1.2/bmi/www.iClarified.co.../16372-500.png Step Six Once the firmware has been verified click the Next button to continue. http://1.1.1.3/bmi/www.iClarified.co...6373/16373.png Step Seven Make sure Cydia is selected and click the Next button. http://1.1.1.1/bmi/www.iClarified.co...6374/16374.png Step Eight Please plug your iPhone into the computer and make sure its OFF then click the Next button http://1.1.1.3/bmi/www.iClarified.co...6375/16375.png Step Nine RedSn0w will now guide you through the steps to get into DFU mode. http://1.1.1.5/bmi/www.iClarified.co...6376/16376.png Hold down both the Home button and the Power button for 10 seconds. http://1.1.1.3/bmi/www.iClarified.co...6377/16377.png Release the Power button and continue holding the Home button until RedSn0w detects the device. http://1.1.1.5/bmi/www.iClarified.co...6378/16378.png Step Ten Your iPhone will now reboot http://1.1.1.3/bmi/www.iClarified.co...6379/16379.png Step Eleven RedSn0w will then begin uploading the new RAM Disk. http://1.1.1.1/bmi/www.iClarified.co...6380/16380.png Step Twelve Once this is complete you will be notified that RedSn0w is done. Click the Finish button. When your iPhone finishes reboot (5 minutes or so). It will be jailbroken with Cydia on the SpringBoard. http://1.1.1.3/bmi/www.iClarified.co...6381/16381.png برامج سيديا التي تعمل جيداً..
|
الساعة الآن 02:20 PM. |
Powered by vBulletin Version 3.8.8
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd