المنتدى العام المشاركات المختلفة في كافة المجالات ...

الرئيسيــــة استرجاع كلمة المرور دليـل الموقــع أكواد الألــوان

إضافة رد
 
أدوات الموضوع انواع عرض الموضوع
منتديات ساسو سوفت - Sasosoft Forums
قديم منذ /21-09-2019, 12:09 AM   #1

كمال رامي
 
الصورة الرمزية كمال رامي

:: عضو فعال ::

كمال رامي غير متواجد حالياً

 رقم العضوية : 70540
 تاريخ التسجيل : 21 - 12 - 2018
 المشاركات : 552
 النقاط : كمال رامي is on a distinguished road
 تقييم المستوى : 12

افتراضي فيرست دبي للغسيل

<*iv align="left">Umm Hurair First Dubai Washing Machine Repair



How to Fix a Washer That Won't Drain
When a washer won't *rain, it's usually because there's a clog or the pump is broken. If you figure out what's causing the issue, you may be able to fix it yourself. To fin* out what's preventing your washer from *raining, you'll nee* to access the parts of your machine to check for *amage or clogs. Then, you can clear out any clogs or replace the broken parts.
[فقط الأعضاء المسجلين والمفعلين يمكنهم رؤية الوصلات . إضغط هنا للتسجيل]
Diagnosing Your Problem
1-Depress your li* switch with your han* to make sure it works. Your washing machine won't *rain if it thinks the li* is open. To check if the li* sensor is broken, fin* the piece on your li* that presses *own when the li* closes. Then, press this switch *own an* listen for a click or check for a "li* close*" light on your washing machine, *epen*ing on your mo*el. If your switch *oesn't seem to be working, you may have a broken li* switch that nee*s replacing.

  • You can or*er a switch online or buy one at an appliance store. Alternatively, hire a repairman to replace the switch for you.

2-Unplug the washer to prevent electrocution before checking other parts. Shift your washer away from the wall so you can access the power cor*. Carefully pull the cor* out of the socket so that the washer isn't connecte* to a power source. This will limit your risk of getting electrocute* while you work on the machine.
    • Don't try to han*le the water in the machine until it's unplugge*. You probably *on't nee* to worry, but it's best to be safe.

3-Use a bucket or pot to remove the water from the washer. You nee* to *rain the machine before you can work on it. First, remove any clothing that's still in the washer *rum. Then, use a plastic bucket or large pot to scoop the water out of the machine. Pour the water *own the sink or bathtub to *ispose of it.
  • This is typically the easiest way to remove water if you're new to home repairs.
  • Place your clothes in a large container, the sink, or the bathtub. They'll likely be sopping wet, so they can *amage some surfaces, such as your flooring.

4-Check if your washing machine's access panel is in the front or back. Your pump will be at the bottom of your washer on either the front or the back. Typically, you'll see 2 small screws at the bottom of the front panel of your washer if it's accessible in the front. If you *on't see these 2 screws, your machine is likely accessible from the back.
  • Typically, top loa*ing washers are more likely to be accessible from the front.

5-Remove the lower screws on the si*e you can access. Use your screw*river to carefully unscrew each of the screws. Place the screws in a safe spot so you can replace them later. As you remove the screws, hol* the panel in place so it *oesn't fall off before you're rea*y.
  • These screws are typically at the corners of the panel near the bottom of the machine.

6-Lift the bottom of the panel to unhook the top an* remove it. Grasp the bottom of the panel with both han*s, then slowly lift it forwar*. As you lift, the top portion of the panel shoul* unhook from the top of the machine. When it *oes, carefully remove the panel an* set it asi*e.
  • The panel will likely feel heavy, so make sure you have a goo* grip on it.

7-Check the grey *rain hose for kinks or *amage. You shoul* see 3 hoses attache* to the back of your washer. The *rain hose will be grey, while the hot water is re* an* the col* water is blue. Look at the grey hose to see if it looks *ente*, crushe*, or bent, which will make it har* for the washer to *rain. If it's *amage*, straighten out the hose or get a replacement from a home improvement store.
  • If you *on't notice any *amage, you might have a clog or another *amage* part.

8-Look at the bottom of the washer for a plastic pump attache* to the *rain pipe. The pump is always at the base of the machine, typically at the back or front so you can easily access it. The pump will be roun* an* cylin*rical with a base, an* you'll see the grey *rain pipe coming out of it. A**itionally, it'll have a hose attache* to it. Typically, this pump is clear or white. However, your pump may be a *ifferent color *epen*ing on the mo*el.
  • If you have your owner's manual, it shoul* have a picture of the pump that you can use as a reference.

9-Check the pump an* surroun*ing hose for a clog. Carefully *isconnect the hose from the pump to look for a clog. Look insi*e both the pump an* the hose to search for clogs. If you *on't see a clog, insert your fingers to feel for one. The clog will likely be something like a small piece of clothing or a wa* of lint. However, it coul* also be something small like a button or coin.
  • If your pump is clear, you may be able to see the clog through the plastic.
  • Water may leak out of the hose or the pump when you *isconnect them.

Tip: You may want to put a clamp on the *rain hose where it connects to the washer so that it *oesn't leak more water while you check the hose an* pump. You can fin* hose clamps at your local home improvement store. [فقط الأعضاء المسجلين والمفعلين يمكنهم رؤية الوصلات . إضغط هنا للتسجيل]

10-Check your pump for *amage if there's no clog. If you can't fin* a clog anywhere, insert your fingers into the pump to see if the spinning mechanism or any other pieces feel broken or *amage*. Look over the entire surface of the pump to check for cracks, warps, or broken pieces. If your pump appears *amage*, you'll nee* to replace it.
  • If you're not sure what the pump is suppose* to look like, this can be tricky. You can use the illustration of the pump in your manual as a reference, but it may be best to call in a professional.

11-Listen for weir* soun*s or leaks coming from your pump. Usually, a *amage* pump will make a weir* soun* or leak onto the floor before it breaks. It may continue to *o this after it's *amage*, *epen*ing on the problem. If you're worrie* your pump is *amage*, turn on your washer an* monitor it for a noise or leaks.
  • If you've been hearing a weir* soun* *uring your previous washes, it's safe to assume something coul* be wrong with the pump. Call a plumber or han*yman to fin* out for sure.

Removing a Clog
1-Grasp a visible clog with nee*le-nose pliers to pull it out. Insert your pliers into the pump or hose. Then, latch the en* of the pliers onto the item clogging your *rain. Slowly begin to tug the item out of the pump or hose.
  • Go slowly so that you *on't break up the clog or *amage the pump. It's possible that a clog insi*e your pump is wrappe* aroun* the spinning mechanism insi*e the pump.
  • It's usually easier to remove a clog from the hose. It shoul* sli*e out easily if you just pull.

2-Fin* the pulley un*er the pump an* twist it to help unwin* the clog. Feel below your machine to fin* a small pulley that's *irectly below the pump. This pulley will turn the spinning mechanism insi*e the pump. As you pull a clog out of the pump, turn the pulley counterclockwise to help unwin* the clog.
  • Turning the pulley will help you avoi* *amaging the pump.
  • If turning your pump counterclockwise isn't helping, try turning it clockwise instea*.

3-Use a plumber's snake to remove a clog from a hose. Detach the pipe an* hol* 1 en* while you place the other in a bucket. Insert the en* of the plumber's snake into the hose. Ease it *eeper into the pipe until you reach the clog. Then, use your han*s to manually turn the snake as you push it through the clog. You shoul* see the clog *rop into the bucket.
  • After you remove the clog, water that was stuck in the pipe may pour out into the bucket.

4-Reconnect your hose to the pump after you've remove* the clog. Sli*e the hose back over the opening on your pump, then secure it in place. Check to make sure that it isn't loose. Otherwise, the hose may leak while the machine is on.
  • Make sure that you haven't create* any kinks in the hose while you were working on it. If there are kinks, it coul* prevent your washer from *raining.

5-Plug up your machine an* see if it works. Test out your machine before you put the panel back on it. First, lower your machine back onto the floor if you lifte* it. Next, put the power cor* back into the socket. Then, set your washer on the rinse cycle an* turn it on. Let the washer run through a rinse an* spin cycle to see if it *rains.
  • If it's still not *raining, it's possible there's a clog you can't get to or that the pump is *amage*. It's best to get a plumber or han*yman to look at it.

6-Replace your access panel if your machine is fixe*. Unplug the machine again before you replace the panel. Then, grasp the panel near the bottom an* slowly lift the top part into place. Hook the top of the panel onto the top part of the washer, then lower the panel into place. Finally, reinsert the screws at the corners.


[IMG]http://www.m9c.net/uploa*s/15689769035.jpg[/IMG]


[فقط الأعضاء المسجلين والمفعلين يمكنهم رؤية الوصلات . إضغط هنا للتسجيل]





  رد مع اقتباس
إضافة رد

مواقع النشر (المفضلة)

الكلمات الدلالية (Tags)
للغسيل, فيرست

أدوات الموضوع
انواع عرض الموضوع

تعليمات المشاركة
لا تستطيع إضافة مواضيع جديدة
لا تستطيع الرد على المواضيع
لا تستطيع إرفاق ملفات
لا تستطيع تعديل مشاركاتك

BB code is متاحة
كود [IMG] متاحة
كود HTML معطلة

الانتقال السريع

RSS RSS 2.0 XML MAP

الساعة الآن 01:44 AM.


Powered by vBulletin Version 3.8.8
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd

جميع المشاركات المنشورة فى المنتدى لا تعبر عن وجه نظر الإدارة

Please dont post any copyrighted materials like cracks , serials , nulled products .. ETC